Mythbusting The Slogan: If You’re Lookin’ You Ain’t Cookin’. True Or False?

June 21, 2013

Today Kingsford Charcoal and the Grilling.com family will be grilling all day in celebration of Summer Solstice, the official mid-way point of Summer barbecue and grilling season.  Be sure to check out recipes here and at our various VIP bloggers sites and also visit our Facebook page here for more all day barbecue and grilling recipes and your chance to win some great prizes!

I know I’m guilty of this saying, especially when other teams are cooking. Here Meathead takes a deep look behind the conventional wisdom on the longest grilling day of the year!

thermodynamics_charcoal2

(Photo Courtesy of Meathead, © AmazingRibs.com) 

 

It is a widely accepted shibboleth, appearing in practically every barbecue book ever written: “If you’re lookin’, you ain’t cookin’”. The message is that when you open the lid of your grill or smoker, cooking slows or stops and each peek adds lots of time to the length of the cook.

That’s because, with the lid on, heat works on the food from above as well as below. Take the lid off, all the hot air escapes and the food cooks from below only.

Well, there are times when you want to cook on one side only but most of the time it is better to cook on both sides. In general, you want to cook thin foods on one side at a time so the bottom surface can brown but heat will not penetrate from above. Then, when you flip, you can brown the other side and not risk overcooking it. In other words, some things cook better in a frying pan and some things cook better in the oven, and a grill with the lid on is just an outdoor oven.

Know-it-alls like this Meathead have often stated that if you open the lid on a smoker that is cooking low and slow ribs or something like that, you add 15 minutes to the cooking time. The logic is that heat and humidity escape, cold dry air replaces them, and if you are using charcoal or wood, oxygen swoops in and feeds the fire and knocks the equilibrium you worked so hard to establish all outta whack. Worse still, I believed, humidity evaporating from the meat or a water pan would escape and you’d end up with drier meat. The warning against lookin’ is meant as a caution to cooks who are constantly basting their food or just admiring their handiwork.

Makes sense, right? But logic isn’t enough for Dr. Greg Blonder, a physicist, entrepreneur, former Chief Technical Advisor at AT&T’s legendary Bell Labs, food lover, and the AmazingRibs.com science advisor and mythbuster. Armed with a stopwatch and a thermocouple thermometer with four probes, he set out to test the theory on his gas grill, his pellet smoker, and his charcoal grill.

gas_grill_peek1

(Photo Courtesy of Meathead, © AmazingRibs.com) 

So one fine October day, with the ambient air temp in the 70s, Blonder cranked his Charmglow three burner standard gas grill to high and after a while it settled in just north of 475°F near the center of the cooking grate about 2″ above the surface.

Then he opened the lid for one minute. Boom! The air temp dove to about 150°F. When he closed the lid, it climbed almost all the way back in a minute or two. “No harm, no foul,” says Blonder.

Then he opened it for five minutes. The temp dove to around 200°F rapidly and stayed there while the lid was up. When he closed the lid it got back up to 400°F pretty quickly but it took almost 10 minutes to level off at more than 450°F and another 10 minutes to get back up to 475°F.

When the lid is opened for only a minute, some of the hot air remains trapped under the lid, the metal in the lid remains hot, and the metal grates on the cooking surface don’t have a chance to cool off. But when it is opened for five minutes, the hot air trapped under the lid bleeds off, ambient air infiltrates, the lid gets cool, and the cooking grates drop in temp. Once the metal has cooled off, it takes time to heat it back up. He explains “The reason it takes so long to reheat is the gas grill, unlike a kitchen oven, has no temperature sensor or feedback. Unaware the temperature has dropped, it doesn’t increase the gas flame in response.”

 

Peeking on a Pellet Grill

looking at a grill temperature

(Photo Courtesy of Meathead, © AmazingRibs.com) 

 

Then he rolled out his MAK 1 Star pellet smoker, set it for 200°F and tossed in a five pound pork butt. He set a probe in the center of the meat, another 1/2″ below the surface, and another about 2″ above the cooking surface near to the meat.

A one minute peek was nearly invisible (the chart for that is not shown). But when he opened it for five minutes, the air temp quickly dropped and bottomed out at just over 100°F (the green line in the chart). But most pellet smokers have thermostat control like your indoor oven, “a negative feedback circuit” in physicist speak. As a result it burned more pellets and pushed more air to the firepot so the recovery was rapid, about 2 minutes, in fact, 1/5 the time it took for the gas grill to recover. In fact, it overshot the mark by more than 50°F and then settled in to the target temp.

But here’s the most interesting data: The probe placed near the meat’s surface dropped only about 3°F (the blue line), and another probe in the center of the meat (red line) continued to climb pretty steadily despite the cooling of the grill, warmed not by the air, but by heat transferred inward from the warm meat on the outside.

Click here for more info on how these clever new pellet cookers work.

 

 

Lookin’ inside a charcoal grill

coal cooking weber grill temperature

(Photo Courtesy of Meathead, © AmazingRibs.com) 

Finally Blonder took out his Weber Kettle and fired it up. With hot coals and a chicken on board, it hit close to 450°F in a hurry. Again he opened the lid for one minute. Boom. Down to 150°F almost instantly. He put the lid back on and the temp recovered in about two minutes to about 400°F.

When he took the lid off for five minutes the temperature bounced back fairly quickly, but never got higher than 350°F, because, even with the lid on, as the coals burn down, the temperature in a charcoal grill slowly declines.

The lesson is that the effect of opening the lid on a charcoal grill like the Weber Kettle is greater than on gas or pellets because the heating potential of charcoal is limited. It eventually diminishes and burns out. So you are not only losing cooking time, you are losing cooking time at a higher temp.

What about the chicken? As with the pork on the pellet grill, the meat responded to the opening of the grill, but only near the surface, and only slightly. The center barely blipped.

 thermal sandwich temperature chart

(Photo Courtesy of Meathead, © AmazingRibs.com) 

 

Heavy duty grills and smokers

Alas, neither Blonder nor I own one of those big sofa sized heavy duty rigs that competition cooks use (that’s one of the top competitors, Johnny Trigg with his Jambo cooker below).

Johnny Trigg with Jambo cooker

(Photo Courtesy of Meathead, © AmazingRibs.com) 

 

Some of these professional cookers are made from steel 1/8 to 1/4″ thick, and all that iron really absorbs the heat. There are also cookers that have double walls, insulation, and some are built of thick ceramic materials to help retain heat. It takes a long time for those babies to heat up and cool off. So Blonder built a simulator. He took two aluminum plates 12″ wide x 12″ long by 1/2″ thick and connected them so they were 1.75″ apart.

He put his metal plate sandwich in the center of his gas grill. He turned on the left and right burners and set them for medium, but left the middle burner off so there was no heat directly below them. He put one digital probe above the sandwich near the lid, and another floating in the center of the sandwich. The first thing you notice is that the probe near the dome is 100°F hotter than the probe in the plate. That’s because heat often builds up under the dome and is often much hotter than down where the food is. “Yet another reason to ignore the built-in dial thermometer” says Blonder. Anyone who reads this site knows this is a crusade I have been on for years.

More on the subject

When the temp stabilized he opened the lid for five minutes. The temp in the dome and the center of the two hot plates dove to around 100°F as it did in the other cookers, and when he closed the lid it recovered quickly, pretty much the same as the others. Yes, the thermal mass made the drop shorter and recovery faster, but as we saw above, the recovery is pretty fast on most cookers.

The big rigs will reduce temperature spikes and recover more quickly than backyard grills because they have so much thermal energy stored up in their significant mass. But they still drop because air is a lousy heat conductor.

How important is constant temp?

Every pitmaster will tell you that it is crucial to keep your pit temp steady. Is it?

Holding a constant temp seems desirable because it is a sign that you are in control, and it helps immensely with timing and predicting when the food will be ready, but does it make a difference to quality? I have never seen it proven, and I suspect it is not as important as they say.

Indoors, our ovens are controlled by a thermostat that turns the heat on, off, on, off, etc. The swings can be plus or minus 20°F but the average is close to the temp you set it for. Despite these ups and downs of as much as 40°F, kitchen ovens still put out great food. This fluctuation happens on pellet grills because they are also thermostat controlled, and on gas grills with gusts of wind, and any other grill or pit when you open the lid.

Remember, meat is mostly water and water responds slowly to temp changes. Think of how long it takes to make water boil. At low cooking temps, the water in meat responds very slowly. That’s why it takes 5 to 6 hours to cook spare ribs at 225°F.

Here’s how the process works, the hot air cooks the outside of the meat. The outside of the meat cooks the inside of the meat. So the outside of the meat feels fluctuations in the air temp, but is slow to respond because it is wet, and evaporation cools the surface. As long as it is wet, the surface temp cannot exceed 212°F. The inside of the meat is even slower to respond because it is not feeling the fluctuations directly. It is just feeling what is happening to the adjacent molecules. So the inside of the meat is not likely to notice temperature fluctuations in the cooker. Think about walking around on a cold day in a really good quality down coat. Your chest is like the inside of the meat and your face is like the surface of the meat. Your chest is insulated and warm, but your face is cold. The temp can drop 20°F and you’ll notice it on your face, but your chest can’t tell.

So I suspect that fluctuations in pit temp have minimal impact on the quality of the interior of the meat. How those fluctuations impact the crust or its flavor, we can only guess. Who knows, it might improve it!

 

An impertinent question for gas grill manufacturers

Blonder’s work raises some more prickly questions.

Why do grill manufacturers continue to use crappy bi-metal dial thermometers in the digital age? And why do they place them in a location high above the food since the food we are cooking is several inches below? But a more important question is why aren’t they installing thermostats?

grill thermostat

(Photo Courtesy of Meathead, © AmazingRibs.com) 

Indoor ovens have had thermostat controls since about 1915.

Wood pellet burning grill/smokers have had thermostats since they first appeared in the early 1990s and they are the hottest new category of grill with more than a dozen manufacturers appearing in the past five years . That’s the state of the art MAK Grill thermostat above, complete with programmable settings and three jacks for meat probes.

The BBQ Guru, a thermostat controller for charcoal grills that controls airflow to the coals first appeared in 2004, and there are two competitors now on the market, Rock’s Stoker and the iQue 110.

When will  one of the high end grill builders put simple thermostats on gas grills? Most replacement thermostats for an indoor oven cost under $100 retail. Surely a major grill manufacturer could add a push button control system just like your indoor oven for about $100. What’s the problem?

Meanwhile, if you own a gas or charcoal grill and don’t have a quality digital oven and meat thermometer yet, please read my article on thermometers and order one.

 

Cold weather

The tests above were conducted on nice summer days. What about the middle of winter? I asked Blonder: “Windy, cold days definitely cool off the interior of the cooker and the meat’s surface pretty dramatically. The penalty is much higher for peeking in the cold. But outdoor temp is less important than cold winds. Air is such a good insulator that even on a cold day it takes time to cool off by air conduction thermal transfer. But a blast of dry, cold air will make a difference. Place your cooker in a wind shielded corner, and you will be OK.”

Conclusion: Another myth busted

So is it true that “If you’re lookin’ you ain’t cookin’”? No, it is not true in warm weather if you open and close quickly and don’t do it often. Yes, it is true if you leave the lid off for long or if you open it frequently, especially in cold weather.

To be sure, the air temp in the cooker drops precipitously, but as we have seen, it also recovers quickly. If you peek for one minute an hour, and the temp drops from 225°F to 100°F for two minutes, the average temp the meat feels is 221°F. Here’s the formula:
(225*58 + 100*2)/60 = 221

This is a drop of less than 2% and in theory that could add about 12 minutes to a 10 hour pork shoulder cook if you open the lid for one minute every hour on a cooker that doesn’t have a thermostat.

If you peek for five minutes an hour, and the temp drops from 225°F to 100°F for seven minutes (keep in mind the temp ramps up and down), the average temp the meat feels is 210°F. Here’s the formula:
(225*53 + 100*7)/60 = 210

This is a drop in temp of about 8% and that could add 48 minutes to a 10 hour pork shoulder cook if you open the lid for five minutes every hour on a cooker that doesn’t have a thermostat.

However, if you have a thermostat cooker like the MAK which overshoots to compensate for drops in temp, there may be no delay in finish time at all.

But the most salient data is not the air temp in the cooker. It is the temp in the center of the meat. Blonder’s data shows that the incursion of ambient air doesn’t seem to have any measurable impact on the center of the meat. That’s because meat is almost all water and fat (a typical average for a pork butt might be about 65% water, 15% fat). Both are great insulators, and a quick peek under the hood isn’t going to drain heat from the meat much more than opening the fridge to take out the milk would warm the meat stored within. Even with the lid open heat continues to work its way towards the center of the meat by conduction. This is even more true the thicker the meat. Warm molecules inside the meat are moving faster than cool ones, and when they jostle the cooler ones they move faster and warm up. The surface of the food may cool momentarily, but the mass of the meat has a lot of thermal energy stored up, especially the longer into the cook you go, and so it keeps on cookin’ regardless of your lookin’.

This, by the way, is the same phenomenon seen when you take a roast or a turkey out of a oven or grill. Called “carryover” the hotter parts of the meat warm the cooler parts in an effort to reach thermal equilibrium. As a result, when you take a piece of meat out of the cooker, the temp in the coolest part of the center can rise as much as 5°F. In this case the meat is still in the cooker, but the hot parts continue to warm the cool parts even though the air in the cooker has dropped to 100°F.

In practice, this residual heat in the thermal mass of the meat may reduce or even negate the loss of cooker temp. We have asked a friend with several thermostat controlled MAK pellet smokers to run this experiment. Stay tuned.

There is another factor that permits you to peek. If you are doing a long low and slow cook and you open the hood when the meat is in “The Stall” phase of cooking, when the temp does not rise much at all because evaporation of moisture is cooling the meat, Blonder estimates the impact will be even less.

What about the moisture? Blonder did not test for that in this series of experiments. A lot of low and slow smokers use water pans to add moisture to the atmosphere and I among many others have always feared that opening the cooker would mess up the relative humidity of the atmosphere inside the cooker. But the more I think about it, that just doesn’t make sense. Moisture in a cooker is not confined to the cooking chamber because they are not airtight. Far from it. Much of the moisture goes right up the chimney and out the sides, so opening the cooker for a few minutes won’t mess up the humidity much. I asked Blonder what he thought and he said “There is much less humidity in a cooker than people think. Besides, most gas grills and pellet smokers change out the entire air volume more than 100 times an hour. In a really tight cooker with the vents mostly closed it’s more like five times an hour. So lookin for a minute just won’t affect the humidity.”

Obviously, if you open the cooker too often the average cooking temp will drop, the exterior of the food will cool significantly and that will slow the cook slightly by absorbing the thermal energy within the meat, but the drop in surface temp is small and recovery will be fast. The amount of energy used should not impact the length of the cook significantly.

How often is too often? Hard to say, but let’s leave it at this: Don’t peek more than you have to, and if you have to peek make it quick, but if you feel the need to turn your meat, to baste, spritz, sprinkle with fairy dust and make incantations, go for it. The advantages of moving meat from hot side to cool side, to checking to make sure nothing is burning, far outweigh the small heat loss. And if you have repeated the catchphrase “If you’re lookin’, you ain’t cookin’” it’s time to stop.

I found it on this site eight times. Took me hours to remove them all, but I have recovered quickly. Just like my grill.

 

Source: Amazing Ribs.com

 

 

 

 

 

Related Topics: Amazingribs.com | Editor's Picks | Looking | Maintaining Temperatures | Meathead | Myths | Opening The Grill | Temperatures | Thermodynamics | Tips

User Guidelines